Patio doors
Sliding Glass Door Repair
Four small wheels carry the whole panel. When they go, the door stops rolling and starts dragging — which is why it got heavy, why it grinds, and why the track underneath is damaged too.
The short answer
Rollers are a wear part. They are meant to be replaced, and replacing them is not a sign the door is finished.
The track usually needs doing too. A dragging panel grinds the rail every time it moves.
Fix it before winter. A door that does not seal is a cold wall in a Maine January.
How a slider works
Two hundred pounds of glass on four wheels
Almost everything that goes wrong with a patio door follows from how it carries its weight.
Part 01
The panel
Tempered glass in an aluminium, vinyl or clad frame, commonly between eighty and two hundred pounds. It is the heaviest moving thing in most houses.
Part 02
The rollers
Four small wheels carrying all of it. A consumable part, meant to be replaced the way tyres are, and the cause of most patio door complaints.
Part 03
The track
A metal rail in the sill. Once a roller collapses, the panel grinds this rail every time it moves, cutting a groove that destroys the next set of wheels fitted.
Part 04
The interlock
Where the moving panel meets the fixed one. It has to seat along its full height, and in a Maine winter a poorly seated interlock is a cold line you can feel from the sofa.
Part 05
The weep channels
Drainage beneath the track, meant to send water back outside. Blocked, they hold meltwater that freezes solid and distorts the rail.
Part 06
The latch
Catches a keeper on the jamb. A panel that has dropped a few millimetres takes the latch out of register and the door stops locking.
Worth doing first
What to do about a dragging slider, in order
This is the one repair where waiting reliably makes the job bigger, because the damage is mechanical and happens every time the door is used.
Stop forcing it
Every heave against a collapsed roller cuts the rail further. If it has got hard, leave it mostly shut until it is looked at.Costs nothing and saves the track.
Clear and flush the drainage
Blocked weeps hold water that freezes. In Maine that is what turns a worn door into a bent rail over one winter.Prevents the expensive failure.
Replace the rollers
Sealed steel-bearing units, load-rated for the panel. The core repair and usually a single visit.Restores the door to one-finger operation.
Deal with the rail at the same time
Dressed or capped in stainless. Fitting new wheels onto a grooved rail buys about a season.The difference between one visit and two.
Renew the interlock and weatherstrip
Hardened gaskets are why the closing edge is cold. While the panel is out is the cheapest moment to do it.Where the heating saving actually is.
Reset the latch
Once the panel is at the right height, the lock usually works again with no new hardware.Security restored for nothing.
The honest comparison
Repair the slider, or replace it
Patio doors attract replacement quotes faster than anything else in a house.
Repair
Nearly always the answer
- The frame is square and the glass is sound
- Rollers, track, latch or seals have failed
- The panel lifts out cleanly for service
- The rail is worn but the sill is solid
- A common system with parts readily available
- Costs a small fraction of a new door
Replace
Occasionally justified
- The frame has corroded or racked out of square
- The sill is damaged beyond capping
- The panel frame itself has failed
- A discontinued system with several faults at once
- Rot in the structure beneath the sill
A capped track and a set of steel-bearing rollers costs a small fraction of a replacement patio door and typically outlasts the hardware that came with it.
Maine conditions
What Maine does to a patio door
Ice, salt and a long season where the door is shut and expected to seal.
Ice in the track
Maine freeze-thaw is relentless in the shoulder seasons. Water standing in a blocked sill freezes, expands and distorts the rail, and a forced frozen panel is how rails get bent and glass gets cracked.
Snow drifting against the sill
Snow piles on a deck, melts in afternoon sun and refreezes overnight. If the drainage is blocked, that water has nowhere to go but into the track and eventually the room.
Winter grit and road salt
Carried in on boots all season and walked straight into the door track, where it mixes with old lubricant into an abrasive, corrosive paste. It is the leading cause of early roller failure here.
A door expected to seal for seven months
Unlike a milder state, a Maine patio door spends most of the year shut and working as a wall. Hardened interlock gaskets and a dropped panel are a measurable heat loss, not a minor irritation.
Not worth your money
Four things not to do
All four of these we are regularly called out to undo.
×
Forcing a frozen door
Thaw it. Forcing a panel frozen into its track bends the rail and cracks glass, and the real fault is the blocked drainage that let the water sit there.
×
Oiling the track
Oil holds grit and salt against the metal, which is exactly the grinding compound that wore the rollers out. Dry silicone, always.
×
Winding the rollers up to hide a drag
Adjusting the height to lift a dragging panel masks collapsed bearings for a few weeks and puts the door out of square while it does.
×
New rollers on a grooved rail
The most common false economy in this trade. The wheels are flat again within a season and the second visit costs more than doing both would have.
Coverage
Sliding glass door repair across Maine
A mobile service covering the whole state, from the southern coast to Aroostook. Pick your town below, or call and we will come to you.
Sliding Glass Door Repair Across Maine
Questions
Patio door questions
Is it the rollers or the track?
Usually both, by the time people call.
If the door drags but the rail still looks clean and smooth, rollers alone. If you can see or feel grooves in the metal, both need doing. We check both at the estimate.
Can a worn track be repaired?
Yes, with a stainless cap.
A cap fits over the damaged rail and gives new rollers a hard, true surface. Taking the frame out of the wall is rarely warranted.
My door is frozen shut.
Let it thaw. Do not force it.
Forcing a frozen panel bends rails and cracks glass, and the underlying cause is usually blocked drainage that will do it again next week.
The door came off its track.
Leave it where it is.
The panel is heavy and awkward, forcing it back can chip the rail or crack the glass, and it will not stay on because the rollers have collapsed.
Cold air comes along the middle of the door.
The interlock gaskets.
They harden over time, and once the panel has also dropped slightly the gap is enough to feel across the room. Renewing them while the panel is out is inexpensive.
How do I stop it happening again?
Vacuum the track, and use dry silicone.
A few times a year, especially at the end of winter. Never an oil-based spray, which holds the salt and grit that wears rollers out.
Related
Other repairs we handle
Windows and doors are the whole business, so whatever has failed, it is on this list.
Next step
Get the slider moving before winter
Free estimates across Maine, with a fixed price before we start.