Sealed units
Foggy Window & Seal Repair
Haze trapped between two panes. It will not clear, it cannot be cleaned, and it does not mean the window failed — only the glass unit inside it.
The short answer
The unit failed, not the window. Frame, sash and hardware are all untouched and all stay.
We do not offer defogging. It clears the view without restoring the seal or the gas fill.
Doing a whole elevation together is far cheaper than one window at a time.
What a sealed unit is
Five parts, and the one that failed is the smallest
Understanding this is the difference between replacing a pane of glass and replacing a wall of windows.
Part 01
Two panes
Separated by a spacer, with a cavity between them that is sealed and usually gas-filled. That cavity is what does the insulating.
Part 02
The spacer
A metal or composite strip around the perimeter holding the panes apart. It also carries a desiccant that absorbs the small amount of moisture sealed in at manufacture.
Part 03
The perimeter seal
A bead of sealant bonding the whole assembly together. This is the component that fails, and when it does, outside air and moisture enter the cavity.
Part 04
The desiccant, once exhausted
It absorbs moisture until it cannot any more. That is the point at which you start seeing haze, which is why fogging often appears suddenly rather than gradually.
Part 05
The sash it sits in
Entirely unaffected by any of the above. It is why a failed unit is a glass job rather than a window job.
Worth doing first
How to approach a house with several fogged units
Rarely urgent, and almost always cheaper done as a planned batch than as a series of emergencies.
Work out how many have actually gone
People notice one and discover four. A walk round on a bright day with the light behind you finds them all.Changes the price per window substantially.
Prioritise the rooms you heat and use
A fogged unit in a spare room costs you very little. The same fault in a south-facing living room is a different proposition.Spend where it does something.
Do them by elevation
Units fail together because they age together under the same sun. Doing a whole side in one visit is markedly cheaper than four separate trips.Most of the cost is the visit.
Check the glazing rebate while you are at it
If the beads or putty have failed, the sash underneath has been wet. That gets repaired before new glass goes in, not after.Stops the new unit failing early too.
Consider low-E if the glass is coming out anyway
On a sun-exposed elevation it is the cheapest moment there will ever be to improve the glass specification.Upgrade at zero extra labour.
The honest comparison
Replace the unit, or replace the window
The quote you get for a fogged window depends entirely on who you ask, and the gap between the two answers is enormous.
Replace the sealed unit
What we do, in nearly every case
- Unit measured on site and made to size
- Beads or stops removed, old unit out, new unit bedded
- Frame, sash, trim and hardware untouched
- Usually under an hour per window to fit
- No disturbance to plaster, paint or interior
- A fraction of the cost of a new window
Replace the window
Only in a few real cases
- The sash is rotten around the glazing rebate
- The frame itself has failed
- A sealed vinyl unit where the glass cannot be separated
- The window was already at the end of its life
- You are replacing that elevation for other reasons
If somebody has quoted you for a houseful of replacement windows because three units have fogged, that is worth a second opinion from a company that does not sell windows.
Maine conditions
Why sealed units fail in Maine
A very wide annual temperature range, damp shoulder seasons and salt on the coast.
A hundred degrees of annual range
Maine goes from humid summer afternoons to deep winter cold. A sealed unit has to hold two panes and a gas fill together across that range every year, and the perimeter seal is what absorbs that movement.
Water sitting in the glazing rebate
Ice dams, blocked drainage and failed putty all keep the bottom of a glazing rebate wet. The seal edge sits in that moisture, and a wet rebate shortens the life of whatever unit goes in next.
Coastal salt on the spacer edge
Along Maine's long coastline, salt-laden moisture works on the spacer and the fixings around it. Units on exposed coastal elevations reach the end of their lives noticeably earlier than the same product inland.
Confusion with winter condensation
Interior condensation and frost are extremely common in Maine houses and have nothing to do with failed seals. Telling the two apart on the phone saves a lot of unnecessary worry, and we are happy to do that.
Not worth your money
Four things not to spend money on
Three of these get sold regularly and one is just a waste of a Saturday.
×
Defogging
Drilling and venting a unit removes the visible haze. It does not restore the seal or the gas fill, and the window carries on performing roughly like single glazing. We do not offer it.
×
Replacing a window over one fogged unit
The unit is a replaceable component. The window around it is fine, and in most cases will outlast several units.
×
Waiting to see if it clears
It will look better on dry days and worse on humid ones. It has not healed. The insulating value went when the seal did.
×
Dehumidifying the room to fix it
The moisture is inside a bonded glass assembly. Nothing you do to the room air will reach it.
Coverage
Foggy window and seal repair across Maine
A mobile service covering the whole state, from the southern coast to Aroostook. Pick your town below, or call and we will come to you.
Foggy Window & Seal Repair Across Maine
Questions
Fogging questions
Will a foggy window clear up on its own?
No, never.
The seal has failed and moisture is permanently inside the cavity. It looks worse on humid days and better on dry ones, but the insulating value has already gone.
Is defogging a real repair?
It improves the view and nothing else.
Drilling and venting a unit does not restore the perimeter seal or the gas fill, so we do not offer it. Replacing the unit is the repair that holds.
Do I have to replace the whole window?
No. Only the glass unit.
The frame, sash, trim and hardware all stay exactly where they are. Fitting a new unit usually takes under an hour per window.
Is frost on the inside the same thing?
Completely different.
Frost or condensation on the room side is indoor humidity meeting cold glass. It is a ventilation and moisture question, not a glazing one, and it is very common in Maine houses in January.
Several windows fogged at once.
Normal, and the cheapest time to act.
Units on the same elevation age together under the same sun, so they tend to fail together. Doing them in one visit costs considerably less per window.
How long does it take?
Two short visits.
Measuring is quick, the unit is made to size, and fitting happens on a return trip, usually under an hour per window.
Related
Other repairs we handle
Windows and doors are the whole business, so whatever has failed, it is on this list.
Next step
Clear the fog properly
Free estimates across Maine, and an honest answer about defogging.